7911/7906 SIP IP Phone firmware files only - Compatible CUCM Versions: 3.3, 4.0,. I have a cisco 7911g phone to be converted from skinny to SIP. I have the downloaded firmware with me (version 9.2.1) and followed the exact same steps as above. The phone boots and I am getting the below tftp log “Serving term06.default.loads” to 192.168.1.201″ where 192.168.1.201 is my cisco 7911g.

Human Health Project is a Northern Ireland (UK) registered charity and a tax exempt 501(c)(3) nonprofit organization in the US. EIN:| NI Charity No. 101323 Footer. Kompjyuternaya prezentaciya prakticheskih dostizhenij professionaljnoj deyatelj. Menslike Hulpbronne fokus op die volgende areas: Aanstellings Vergoeding / Salarisse Diversiteitsontwikkeling Diensvoorwaardes Sekretariaat vir Aanstellingskomitees (senaat) Prestasiekontrakte / werksooreenkomste Instandhouding van personeellyste, -datavaslegging (alle) Sekretariaat vir komitee insake buitewerk Posevaluerings. Write something about yourself. No need to be fancy, just an overview. No Archives Categories. Write something about yourself. No need to be fancy, just an overview. No Archives Categories.

I have a problem with 7911 IP phone. I have installed 2 new 7911 IP phones and registered it on UCM 8.6.2. They have successfully registered but the confugured locale have not been applied. I've done factory reset by 123456789*0# combination, the phone began repeatedly reboot with several minutes interval, showed upgrade screen for several seconds and than showing a Cisco logo with 1 circle with dot in lower left edge on the screen.

I've reset it with *# after that I see a clear screen and the phone flashed its transparent buttons with several minutes interval. In tcpdump I see the phone loads term11.default.loads, UCM sends it and than no activity from the phone.

In term11.default.loads I see the following: Trozkiy:~ mdenisov$ strings./term11.default.loads 'CN=someSigner;OU=someOrgUnit;O=someOrg #CN=someCA;OU=someOrgUnit;O=someOrg O78m wtmckTd a]=I 72Xxl term11.default.loads # This file contains a list of archive image files that will be requested by the # RELEASE load version 9-2-1TH1-13 #HARDWARE_COMP_1 1 jar11sip.9-2-1TH1-13.sbn cnu11.9-2-1TH1-13.sbn apps11.9-2-1TH1-13.sbn dsp11.9-2-1TH1-13.sbn cvm11sip.9-2-1TH1-13.sbn Trozkiy:~ mdenisov$ The phone should be SCCP. Pdf mga wika at dayalekto sa pilipinas7278589 today. How can I troubleshoot thes problem? I have set build all cnf files in service parameters and restarted tftp service. Other phones can register and upgrade successfully.

Is there a way to connect to the phone with telnet, ssh or something else end see what do it needs? Regards, Maxim. Maxim, Yes, 7911 supports SSH but it needs phoneload 9.2.1 in it to support it & at this moment the main issues is that it's not getting on to 9.2.1.

If you refer the for firmware release 9.2.1 it says, For all SCCP/SIP firmware upgrades from firmware release versions earlier than 8.3(3) to version 9.2(1) or greater, you must first upgrade your firmware to an intermediate version (8.3(3) - 8.5(2)) then upgrade to 9.2(1). Therefore, as Paolo mentioned, you might want to upload the phoneload first to mentioned 8.x version on to your CUCM 8.6.2 ( which comes by default with 9.2.1 phoneload for 7911s ) & then once the 7911 gets 8.x phoneload, you may just change the device default value to 9.2.1 & bring them up to the mark as of others. Let us know how it goes. Pls rate the post if it helps. Maxim, Yes, 7911 supports SSH but it needs phoneload 9.2.1 in it to support it & at this moment the main issues is that it's not getting on to 9.2.1. If you refer the for firmware release 9.2.1 it says, For all SCCP/SIP firmware upgrades from firmware release versions earlier than 8.3(3) to version 9.2(1) or greater, you must first upgrade your firmware to an intermediate version (8.3(3) - 8.5(2)) then upgrade to 9.2(1). Therefore, as Paolo mentioned, you might want to upload the phoneload first to mentioned 8.x version on to your CUCM 8.6.2 ( which comes by default with 9.2.1 phoneload for 7911s ) & then once the 7911 gets 8.x phoneload, you may just change the device default value to 9.2.1 & bring them up to the mark as of others.

Let us know how it goes. Pls rate the post if it helps.